Do you have a product that can combine 2 low voltage circuit into one such that I can use a single circuit transformer? I understand the capacity of the transformer has to be big enough for the combined load. Thanks.
All of our TRANSFORMERS have a 25-amp circuit breaker per circuit. You can combine several feeds under one lug as long as you don''t exceed 300 watts. (300 watts divided by 12 volts equals 25 amps) Check out our DESIGNING LOW VOLTAGE LIGHTING SYSTEMS information page. I would recommend that you have at least 12/2 LANDSCAPE CABLE on each of your lighting runs.
Labels: Landscape Cable, Low Voltage Lighting, Low Voltage Transformers
I am having a tough time locating miniature ( 3" - 6") electrical or battery operated up-lights that one can sit on a counter top or the floor. Do you carry such a product or have a connection with a company that does? Thanks.
We only have a limited selection of BATTERY OPERATED LIGHTS. We have TWINKLE LIGHTS, PICTURE LIGHTS and PIANO LIGHTS that operate on batteries.
Labels: Art Lighting, Battery Operated Lights, Christmas Decorations
Are there special design concerns when a lighting system is immediately adjacent to an underground sprinkler head/system?
It is always best when designing a outdoor lighting system to avoid mounting lights adjacent to sprinkler heads for obvious reasons. UP LIGHTS, which always have lenses, will accumulate lime on the lens from the water restricting the light output. Less expensive PATH LIGHTS generally don''t have lenses or sprinkler guards and water constantly spraying the light bulb can cause it to crack or fail. SOCKETS over the long run begin to deteriorate from the constant moisture. So, if at all possible, avoid mounting a light near sprinkler heads.
Labels: Low Voltage Path Light, Low Voltage Sockets, Low Voltage Up Lights
House of Troy, one of the leader's in art lighting equipment, has introduced a new line of
MODERN TABLE LAMPS and
MODERN FLOOR LAMPS. These handsome lamps will make your home stand out with it's unique tilted head. Available in Weathered Brass, Satin Brass, and Stain Nickel.
In addition to these new fixtures, House of Troy manufactures several
TRADITIONAL SWING ARM LAMPS,
WALL MOUNT LAMPS as well as
PICTURE LIGHTS and
PIANO LIGHTS.
Labels: House of Troy Lighting Fixtures, Modern Lamps, Picture Lighting
I am replacing flouresent lighting in my kitchen with recessed lighting. I realize that I should install the lights 6 to 7 feet apart. Does it matter the size of the fixture, 4", 5" or 6"? Or, is it just the bulb I use that I need to consider? My wife wants to go with a smaller 4 or 5 " size for looks. I was going to put in 6".
The size of the recessed lighting fixture will determine the maximum wattage lamp you can use. For example, a 4" fixture with a PAR20 halogen lamp has a maximum wattage of 50-watts. A 5" fixture with a BR30 incandescent lamp has a maximum wattage of 85-watts. A 6" fixture with a PAR38 halogen lamp has a maximum wattage of 120-watts. For the size kitchen you have ddescribed, I would go with a 5" LIGHTOLIER RECESSED DOWN LIGHT or a 5" HALO RECESSED LIGHT.
You should also install a LUTRON DIMMER CONTROL on the lights to regulate the intensity and to set the mood!
Labels: Halo Recessed Lighting, Lightolier Recessed Down Lighting, Lutron Lighting Controls
I have outdoor lighting - black box with only name on it as TWILIGHT LOW VOLTAGE LIGHTING SYSTEM Model: CB-150MD Trying to locate just the photo sensor - do not need the entire unit. Works fine as ON all the time, it''s the dusk-to-dawn that won''t operate, and I believe the photo sensor is bad. Can you help me find a suitable sensor to go with this unit ?
I am sorry, but we do not carry what you are looking for. We do have PHOTOCELLS that you can use to control the (120-Volt) line side of your transformer.
Labels: Lighting Controls, Outdoor Lighting Systems, Photocells
Would like to have indirect lighting hid behind crown molding in our hallway. Will bending ropelightingat a 90 degree angle either inward or outward break the electrical connections within the rope.
As long as it is a slow radius turn the LIGHT ROPE should be fine going around the corner of your cove. I prefer the pearl white color option for cove lighting applications. Check out our COVE LIGHTING INFORMATION page for additional ideas, suggestions and indirect cove lighting products.
Labels: Cove Lighting, Indoor and Home Lighting, Rope Lighting
where do i find solar powered lighting for deck stairs that mounts flush to the stair riser?
I am not aware of a fluch mount solar light designed specifically for stair risers. By design, the solar powered lights must have solar panels pointed at the sun to collect energy and recharge. A step light would require a remote panel to be oporational.
Have you looked at our LOW VOLTAGE STEP LIGHTS that are designed for steps, decks, stairways and other patio applications? They are very easy to install and service and will be more reliable than the solar option over the long haul.
Labels: Low Voltage Applications, Outdoor Landscape Lighting, Step Lights
What is the difference between n.p.s. threads and n.p.t. ? Are there adapters to change from 1/2 inch male nps to 1/2 inch female npt. Help !!!! I''m trying to retrofit fixtures for a driveway project. Thanks in advance.
NPS threads are straight pipe threads that when assembled with other NPS threaded components will provide free and loose mechanical joints without pressure tightness. NPT threads are tapered pipe threads that when assembles with other NPT components and a sealer will produce a pressure tight joint.
Most of the LANDSCAPE LIGHTING FIXTURES we sell have NPS threads. You can use a standard pipe thread compound on NPS threads to prevent water from getting into the fixtures or junction boxes.
Labels: Landscape Lighting, Outdoor Lighting Applications, Retrofit Fixtures
We''ve got a 35'' X 16'' Aluma-wood patio cover. It''s an aluminum patio cover with a laticed, non solid top. I would like to put 4 cannister or puck lights directly over the BBQ island and 3 surface mount ceiling lights spread across the 35'' length. BBQ lights will be on one dimmer switch and ceiling lights on another.First, I''d like the lamps to be bright, maybe brighter than incandescent bulbs. I''d also like the dimmers for mood when necessary. Halogen or xelogen bulbs are the way to go, right? Can dimmers be used with halogen or xelogen bulbs like incandescent bulbs?Second, lights that take incandescent bulbs cannot also take halogen/xelogen bulbs, correct? If so, where does one find decorative/stylish, "outdoors use" halogen/halogen lights? I've looked everywhere and am coming up short. Would I be better sticking with incandescent bulbs?
Sounds like a great project! I can tell you now, forget using PUCK LIGHTS outside. They are not weatherproof and will look terrible. I do prefer the halogen source over the incandescent source due to lamp life and color.
You have a couple of options for LOW VOLTAGE HANGING LIGHTS in copper, HANGING ACCENT LIGHTS in brass or DIRECTIONAL ACCENT LIGHTS that will look good on your arbor.
How about a WEATHERPROOF CEILING FAN? We have a full line of WESTINGHOUSE FANS so of which are designed for wet locations.
Labels: Directional Accent Lights, Low Voltage Hanging Lights, Westinghouse Fans
I need new path light. The 10" Pagoda Path Lights AL0310 seem appropriate. But I am confused. Is the light spread a circle with 24 foot diameter? Is that achieved with the lamp that comes with the fixture? Do different lam;ps produce different light spreads?
The Focus Lighting - 10" Pagoda Path Lights AL0310 path light is perfect for illuminating walks, paths and driveways. The diameter of the circle is determined by the mounting height. The light bulb determines intensity, not so much the spread! I like the 20-watt SC base holgen lamp myself. If you want to spread more than a 10'' diameter, you need to go with a taller stem. Be careful not to go to high as you begin to get glare from the fixture. They are designed to be installed below eye level for maximum enjoyment.
You might also consider the Techlight 10" Mushroom Path Light 12 Volt AL10A as another option.
Labels: Low Voltage Lighting, Outdoor Landscape Lighting, Path Lights
Is there an easy way to size an exhaust fan for my bathroom? You have so many choices!
Picking the right
VENT FAN is always hard for a consumer. We get lot's of questions regarding
NUTONE FANS and
PANASONIC FANS.
So we created a simple CALCULATOR to help you determine the minimum CFM fan needed for HVI's recommended 8 air exchanges perhour as recommended by the manufacturer. CFM stands for cubic feet per minute of air.
If you need further assistance to select the right product for your home, just give us a call at 800-239-2939.
Labels: Nutone Fans, Panasonic Fans, Ventilation Systems
Do you have a typical light standard detail for a 30 foot pole(I am looking for the detail of what needs to be put in as far as concrete and rebar to support this pole)Thanks
The standard CONCRETE FOOTING for a 30'' pole is 24" diameter approximately 6-8'' deep. Of course, soil conditions vary from state to state, so it''s a good idea to have a local engineer review the WIND ZONE CHART and sign off on the final footing design.
For more information concerning OUTDOOR LIGHTING POLES you should take a look at our OUTDOOR POLE LIGHTING INFORMATION PAGE.
Labels: Commerical Pole Lighting, Outdoor Lighting Poles, Parking Lot Lightin
In 12 volt lighting, how far can I safely run 20-awg wire? (if a specific example is needed, use 13V, 3.5A transformer
20 guage wire is really too small for 12 volt applications. Check out our POWER CABLE CALCULATOR to see what works best for your application We also have a DESIGNING A LOW VOLTAGE LIGHTING SYSTEM page for more information on the subject. You should consider at least 14 guage wire for your project.
Labels: Low Voltage Lighting, Outdoor Lighting System, Power Cable Calculator
I noticed in a previous post that you carried Westinghouse Weatherproof fans. Would these be suitable for use in an exposed pergola?
Yes, some of our WESTINGHOUSE CEILING FANS are for wet locations and others are for indoor use only. I recommend that you take a look at the folowing fan:
Westinghouse - Pacific Paradise Ceiling Fans - 78790
Item Number: WST 78790
I see a lot of contractors install a peice of plexiglass on top of the pergola to protect the fan from direct expose. These fans have gaskets and are designed to work outdoors.
Labels: Ceiling Fans, Weather Proof Ceiling Fan, Westinghouse House
Our manufacturers have asked us to help them clear the shelves of overstock and discontinued rope lights and lighted Christmas ornaments . Our
BLOW OUT SPECIALS are only good until supplies last. This is a perfect time to load up on
OUTDOOR CHRISTMAS DECORATIONS at some of the best prices of the year. They make great gifts for those "hard to buy for" friends and family members. As these prices, you might want to use them as a holiday decorations at festivals, christmas holiday celebrations, neighborhood associations or at church.
ROPE LIGHT FIXTURESWe also have a great selection of TWINKLE LIGHTS, PRE-LIT CHRISTMAS TREES and WREATHS!
Labels: Holiday Blow Out Specials, Outdoor Christmas Decorations, Twinkle Lights
Our deck has 4x4 posts with pre-drilled holes for wires. We need about 10 small "scallop" style lights that will mount on the posts at a height of approx 36". The actual post size is 3 1/2 x 3 1/2.
We have a wide selection of OUTDOOR LOW VOLTAGE LIGHTS that will work in your situation.
We have a handsome HADCO POST TOP LUMINAIRE that may be of interest to you.
We also have some SCOOP LIGHTS that will work.
Labels: Low Voltage Outdoor Lighting, Post Lights, Scoop Lights
First, your website is impressive! I was unable to find out how to convert my kitchen fluorescent strip lighting to incandescent. I''ll need to add under counter lighting to spread more light. I look forward to your response and professional advice. thanks!
We are certainly glad that you like our website. Thanks!
You have a couple of options for converting your FLUORESCENT UNDER CABINET LIGHTS to HALOGEN UNDERCABINET LIGHTS or XENON UNDER CAB LIGHTS. Both of the quality task lights will retrofit with out having to rewire your lights. Both can be dimmed using a LUTRON DIMMER CONTROL.
Give customer service a call at 800-239-2939 to discuss your installation and which fixture is right for you.
Labels: Lutron Dimmer Control, Task Lighting, Under Cabinet Lighting
Currently designing landscaping for our new custom home, so please send information on lighting and design services. Of particular interest is down lighting for large oak trees on our property. Thank you.
If you are interested in down lighting, I would suggest that you look at our MERCURY VAPOR DOWN LIGHT KITS. These packages are designed for the "Do It Yourselfer" in mind! They include all the necessay items you need to perform a professional installation. The DOUBLE 100 WATT KIT is probably the most common wattage for Oak trees. If the tree is very tall, you should upgrade to the 175 WATT KIT.
If you have any questions, just give us a call at 800-239-2939.
Labels: Down Light Kits, Mercury Vapor Fixtures, Moonlighting
Just stumbled upon your web site -- very helpful, and I''m likely to become a good customer! My questions: I''m installing a pool in my back yard. I already have Niles Outdoor Rock Speakers (4 pair) that I''m placing around the pool/spa/patios. If I want to add a subwoofer for better bass response, do I just need one for the area as a whole, or should I have multiple subwoofers? The overall "pool/deck area" is probably something like 60'' by 60'' or thereabouts. Second question. I want to install a "moon light" in a tree near the pool for some ambient down lighting. What light do you recommend for that application? I assume it''s 120V, rather than low voltage, but if I''m mistaken, let me know. Thanks.
Hey, thanks for the kind words. I certainly hope that we can assist you with your audio and lighting needs!
I would recommend that you go with two SUB WOOFERS for that size yard. Since you already have eight speakers this should do the trick. Your yard will ROCK!
As for lighting outdoor landscape lighting equipment, Watt it really depends on the height of the tree and how bright you want the light. Here are my suggestions:
If your mounting height is 20'' high or less go with a 50 WATT MERCURY DOWN LIGHT VAPOR KIT.
If your mounting height is 30'' or less go with a 100 WATT MERCURY VAPOR DOWN LIGHT KIT.
If your mounting height is 40''or over go with a 175 WATT MERCURY VAPOR DOWN LIGHT KIT.
Depending on the position of your pool you might want to go with a two fixtures in the tree. Sound like you have a great yard! Give us a call at 800-239-2939 for more assistance in selecting your products.
Labels: Mercury Vapor Lights, Outdoor Landscape Lighting, Sub Woofers
Dedicated to bringing you the best in outdoor lighting products, we are proud to introduce the new Palm Tree Base.
Specially designed to fit on the trunk of a palm tree, this base has a curved housing and is equipped with your choice of 6 foot or 12 foot straps. Add this to the mounting slots on the top and bottom of the base and you can bet that this base will hold the weight.
The Palm Tree Base Mount and Strap B16 features include: The unique adjustable nylon strap and spring loaded latch provide the ultimate in adjustable mounting techniques for any type of tree or any OUTDOOR LANDSCAPE LIGHT. Check out the new standard in Palm tree mounting today!
Labels: Nylon Straps, Outdoor Landscape Lighting, Palm Trees Base
Apparently terminal C is used for a 3 wire photo cell to control the lights. How is this done?We have an 88, 100 and 200 watt transformers with a timer each. I want the system to turn on at dusk and turn off at 11:00, without having to adjust for daylight changes through the seasons. This would involve putting a photoelectric sensor in the line after the power transformer or using terminal C. The transformer timer would turn power on at say 4:00 p.m. but the lights would not until it got dark. They would then turn off at 11:00 from the timer. Is there a sensor which is available that works on a 12 volt system? I have tried one of your 120 volt ones - but the 12 volts is not enough "juice" to trigger the sensor to turn off. Or is this what the C terminal is for? ThxRuss.
You are making this way to complicated! Just install a MECHANICAL TIME CLOCK to control the TRANSFORMER. If you want, you can install a PHOTOCELL after the time clock and before the transformer. I do not know of a 12 volt photocell or time clock.
Labels: Low Voltage Transformers, Mechanical Time Clocks, Photocells
I have looked at your different picture lights and see that the 14" Richardson picture light has an option of a switchon the frame. I am going to need 3 or 4 of these and would like to buy the picture lights that have the switches already on the light frame, if possible. Can you give me your expert opinion on which is the best quality for the most reasonable price? Thank-you.
All of our HOUSE OF TROY PICTURE LIGHTS have a thumb switch on the cord. What I do is staple the thumb switch to the frame, using a T18 staple gun, and them staple the excess wire. If you have a RECESSED CLOCK RECEPTACLE behind the painting this works well because the painting hangs flat against the wall. Personally, I like the TRADITIONAL PICTURE LIGHTS because of the variety of sizes and finishes or the CONTEMPORARY PICTURE LIGHTS.
Labels: House of Troy Lighting Fixtures, Picture Lights, Recessed Clocks
Are you looking for a challenging and exciting office administration position in the Houston area?
We are Residential Landscape Lighting & Design (RLLD) the internet’s fastest growing and most successful online venue for lighting products in the country! RLLD is an online reseller that is currently seeking to fulfill an Office/Admin clerical position to provide support to the Controller and our valued customers through various activities. Our team of lighting professionals is looking to expand and become a 'final destination' for the industries very best talent on the internet.
Duties include:
Receptionist
Customer Service Issues
Data Entry/Reports
Accounts Receivable
Reconciliations
Special Projects
The ideal candidate should have a minimum of 3 years proven successful experience in the following areas:
Excellent phone demeanor and experience answering phones
Possess accurate typing and 10-key skills
Microsoft Office Suite to include: Word, Excel and Outlook
Ability to multi-task
Strong communication skills
Experience with data entry
Attention to detail
Dependable
If you have a desire to sell and are highly motivated to achieve your financial goals, please contact us today! To apply please contact our Human Resources Department or fax resume with cover letter to 713-707-4161. This is an outstanding long term opportunity for the right person!Labels: Experience, Job Duties, Office Administration Position
I am in the process of building some wood bookshelves for a client in his home office. He has asked me to put some lights on the shelves. I see that you have a wide selection of shelf lighting products to choose from, which is very helpful. How do I light each shelf with the same amount of light if I use glass or wood shelving?
We do have a great selection of
CABINET LIGHTS and
SHELF LIGHTING PRODUCTS. If you are planning to use glass shelves you have two mounting options: From the top of the cabinet down, or mounted vertically on both sides of each opening.
TOP DOWN METHOD OF SHELF LIGHTINGDepending on the size of the cabinet and space above the cabinet you may want to use
PUCK LIGHTS or
LOW VOLTAGE RECESSED LIGHTS as your light source. The puck light fixtures are best suited for small to medium sized cabinets with glass shelving. The low voltage recessed lights are better for medium to large cabinets where more light is desired.
VERTICAL MOUNT METHOD OF SHELF LIGHTINGFor successful vertical mounting of lights it is best to provide a 2" wood reveal or stile on the cabibets to hide the lights. If the shelfs are adjustable, you should also provide a 1" space from the front of the shelf to the back of the reveal to accomodate the light fixtures and to clear the shelves.
Our
PHANTOM XENON VERTICAL SHELF LIGHTS are the most effective and flexible lights that we offer. Used in conjunction with a
TRANSFORMER and
LOW VOLTAGE DIMMER CONTROL these lights will more than please your client! Check out our
GALLERY SECTION for more ideas!
Visit
PHANTOM LIGHTING.COM to learn more about ways to illuminate shelving, cabinets, breakfronts, antiques, coves, display cabinets or bookcases.
Labels: Dimmer Controls, Phantom Lighting, Undercabinet Lighting Fixtures
I am installing new drop ceiling tiles at my office and need some new
FLUORESCENT FIXTURES to finish off the job. What is the cost and availability for 2' x 2' fixtures and 2' x 4' parabolic fixtures?
Both sizes of the lay-in fluorescent fixtures are in stock and their is very little difference in cost between the two. The
2' x 2' fixtures look better in smaller offices or in a ceiling with the same size tiles. They run about $70.00 or less.
Some of the features of this fixture include:Optional two 6" U-shaped T8 bulbs
Each bulb is 32Watts
9 louver cells
3" deep louvers
Computer-aided housing design allows for optimum
luminaire efficiency and visual comfort
Aluminum louver surfaces plated with anodized, semi-specular aluminum, low iridescent finish
Spring-loaded cam latches and die-formed T-hinges for louver insertion from either side
Floating door with black reveal
Removable louver seal eliminates dust build-up and protects lamps during installation
Housing constructed of structurally embossed heavy gauge, cold rolled steel
Access plate provides top access to wire way
UL/
CUL listed
All metal parts painted after fabrication following treatment with phosphate rust inhibitor
Finish coating of housing reflecting
surfaces with white, high reflectance polyester powder
The
2' x 4' parabolic fixtures produce more light and require fewer fixtures to light the space. They run about $80.
oo or less.
Some of the features of this fixture include:
Optional three 48" T8 bulbs
Each bulb is 32Watts, 4100K
18 louver cells
3" deep louvers
Computer-aided housing design allows for optimum
luminaire efficiency and visual comfort
Aluminum louver surfaces plated with anodized, semi-specular aluminum, low iridescent finish
Spring-loaded cam latches and die-formed T-hinges for louver insertion from either side
Floating door with black reveal
Removable louver seal eliminates dust build-up and protects lamps during installation
Housing constructed of structurally embossed heavy gauge, cold rolled steel
Access plate provides top access to wire way
UL/
CUL listed
All metal parts painted after fabrication following treatment with phosphate rust inhibitor
Finish coating of housing reflecting
surfaces with white, high reflectance polyester powder
In addition to parabolic fixtures we also have a great selection of
STANDARD FLUORESCENT FIXTURES in both sizes! Give a call toll free at 800-239-2939 for quantity discounts and overstock specials on
COMMERCIAL LIGHTING FIXTURES.
Labels: commercial lighting fixtures, Fluorescent Fixtures, Fluorescent Troffer Lights
Where can I find some quality reproduction table lamps, sconces and chandeliers for my home?
We have a great selection of
REPRODUCTION ANTIQUE TABLE LAMPS, sconces and chandeliers from 2oth Century Lighting. These beautiful decorative indoor table lamps are great for living rooms, bedrooms, dens, or anywhere in you home. If you don't see one that you like, just let us know as we are adding products all the time!
We have a wide varieties of colors available: Antique Brass(shown), Worn Blackened Paint, Distressed Painted Iron, Old Nickel, Satin Nickel, Tarnished Copper, Oil Rubbed Bronze, Anitque Silver, Pewter, Aged Gold.
Check out all our
RESIDENTIAL HOME LIGHTING PRODUCTS as well as OUTDOOR
LANDSCAPE LIGHTING EQUIPMENT.
Labels: Antique Table Lamps, Home Lighting Products, Landscape Lighting Equipment
Summer is over and we are just six short months away from the Christmas holiday season. Finding good
PRE LIT CHRISTMAS TREE in stock becomes harder the longer you wait in the year. Our selection of
LIGHTED CHRISTMAS TREES,
LIGHTED GARLAND and
LIGHTED WREATHS are in stock and ready to ship.
For more information on how you can
DECORATE YOUR TREE this season visit the professionals at Residential Landscape Lighting & Design for all your
HOLIDAY DECORATING SUPPLIES. Call us toll free at 800-239-2939 to make this one of your more decorated holiday seasons ever!
Labels: Artifical Christmas Trees, Holiday Decorating Supplies, Holiday Lighted Decorations
We have low voltage outdoor landscape lighting for about 4 mo. now. Worked fine until some heavy rains came, not the first mind you and suddenly no lights. Tripper not turning lights on, manual either. Checked circuit breaker, socket is covered and dry, replugged and still no lights. Could water have short circuited where water may have entered through the piercing of the quick connect? Please help
I suppose that could happen, but is is highly unlikely that all the fixtures would fail at the same time. Sounds like your transformer to me.
I would disconnect on of the fixtures and connect it directly to the TRANSFORMER as a test. If the fixture lights up, then the problem is in the wiring or the connectors. If nothing happens, you will need to replace the power supply.
Labels: Low Voltage Lighting, Magnetic Transformer, Outdoor Landscape Lighting
Our extensive selection of
WESTINGHOUSE CEILING FANS are the most stylish, energy efficient, and highest quality you will find anywhere. For over 100 years Westinghouse has built a strong reputation for building reliable and useful products for homes and offices, remaining always at the forefront to technological and engineering advancements. Whether you are looking for a traditional or contemporary style ceiling fan, you can find the exact look you desire among our quality selection. For those looking for quick installation,
Westinghouse's patented InstaLoc™ Technology allows you to install a ceiling fan in a matter of minutes, without the help of an electrician.
Ceiling fans can bring numerous energy saving benefits to the home. Most ceiling fans use only about as much power as a 100 watt light bulb. When used properly, ceiling fans can save you money in utility bills in both the winter and summer months.
If you have any questions about the contemporary, traditional, indoor/outdoor or InstaLoc ceiling fans we offer, do not hesitate to
CONTACT the experienced professionals at Residential Landscape & Lighting Design. Our friendly staff is happy to answer any questions you may have about our selection, or how a ceiling fan may be best integrated into your indoor or outdoor application. We can be reached toll free at 800-239-2939.
Labels: Ceiling Fans, Traditional Ceiling Fans, Westinghouse House
My timer will work shutting lights off but not turning on. The lights will come on if I manually turn the timer''s dial. Once I do this then the timer works. It will shut lights off at corredt time. When it goes back to time to turn lights on it does not move. I have to move manually.
You might need a new set of TIMECLOCK TRIPPERS to solve your problem. We also have replacement TIMECLOCKS if you decide to purchase a new one. We have both INTERMATIC TIMERS and TORK TIMECLOCKS.
Labels: Intermatic Timers, Lighting Control, Time Clock Trippers
I''m installing a new 12'' x 20'' patio cover and I want to put lighting in it for entertaining and playing games. I''m thinking of overhead spot lights or perhaps suspended pendulum lights, but I can''t find anything that I like. Any suggestions?Thanks for your help.Joe Reese
You might take a look at out FOCUS HANGING LIGHTS for your patio cover. Since they are low voltage lights they are easy to install, attractive and very effective. You will need a TRANSFORMER to power the lights and a LUTRON DIMMER CONTROL to adjust the intensity.
Labels: Hanging Lights, Lutron Lighting Controls, Magnetic Transformer
I want to make sure that I hook up the GE transformer I bought properly. It is a 1000watt with 4 primary wires and 4 secondary wires. If I am reading the wiring diagram correctly, to go from 120 volts to 12 I need to hook two of the primary''s and two of the secondary''s together. So do I have to be concerned about which primary wire gets hooked to the hot wire? Also, the way the lights were hooked up before we bought the house was there were four 250 watt transformers hooked to 4 low voltage wires. Will it create any problem to hook these 4 sets of wires together to attatch to the new transformer?
On your GE Buck/Boost Transformer should have several wires labeled H1, H2, H3, H4 on the primary side and X1, X2, X3, X4 on the secondary side.
For 120 volt input and 12 volt output connect the following wires:
H1 to H3
H2 to H4
X1 to X3
X2 to X4
Labels: Boost Transformers, Low Voltage Transformers, Transformer Wiring
I have read your site to help design my landscape lighting which is very helpful, however I could not find what the normal distance of path lights with 11 watt lamps on walkway? Also, is a 20 watt spot OK to use to accent the house? Thank you!
The distance between PATH LIGHTS really depends on the height and style of the fixture. Sounds like you are using a MALIBU lighting fixture with 11 watt lamps. Those low voltage lights should be spaced approximately 6 to 8 feet apart. If you had a taller fixture with a higher wattage lamp like the Tech light - Low Voltage Copper Path Light TLSCPL12 you could go 8 to 12 feet apart.
The 20 watt MR16 is a good lamp for washing the front of your house.
Labels: Copper Path Lights, Landscape Design Lighting, Malibu Lighting Fixture
Timer runs until red pin reaches the switch, then it will not move any further and lights will not switch on. Unit seems to get stuck. Why?
Sounds like the small gear is spinning on the shaft of your time clock when the tripper hits the on lever. I would recommend that you replace the motor or install a new TIME CLOCK SWITCH CONTROL.
Another inexpensive solution to your problem is to install a PHOTOCELL CONTROL for your outdoor lighting system.
Labels: Mechenical Timer, Photocell Control, Time Clock Switch Control
I''m looking for information on how to design and install low voltage lighting around the perimeter of my garden.
Check out our LOW VOLTAGE LIGHTING DESIGN PAGE for tips and help understanding LOW VOLTAGE LIGHTING and how to use them. We have PRE-PACKAGED OUTDOOR LIGHTING KITS to make things easier for you!
Labels: Garden Lighting, Low Voltage Lighting,
